MATERIAL SAFETY DATA SHEET

PRODUCT NAME : INDUSTRIAL ORGANIC SOLVENT


Synonyms INDUSTRIAL ORGANIC SOLVENT
Company Name NOVA COMPANY PRODUCES LUBRICATING OIL FOR EǪUIPMENT AND ENGINES
Address Block :7, Building :84, Lic No:208142, East Ahmadi, Kuwait
Contact Number +965- 60410970 / 51314011
Email :info@novalubricantskw.com

COMPOSITION/INFORMATION ON INGREDIENTS


This product is a complex mixture of Hydrocarbons and Mineral oils.
Chemical Name CAS NO. Concentration %
INDUSTRIAL ORGANIC SOLVENT 64742-88-7 100%
This product does not contain any hazardous ingredients.

HAZARDS IDENTIFICATION


Statement of hazardous/dangerous nature.

Slightly causes irritation in case of eye and skin contact. Inhalation causes headache and nausea. Ingestion causes burning sensation, vomiting and loss of concentration. Potential Chronic Health EXects: Not available.

FIRST AID MEASURES


This product is a complex mixture of Mineral oil.
Inhale Inject Skin Contact Eye Contact
Inhalation of mists, fumes or vapor causes irritation to the nose or throat or coughing. Move to the region of fresh air. If symptoms persist obtain medical advice. If contamination of the mouth occurs, wash out thoroughly with water, except as a deliberate act. The ingestion of large amounts of product is unlikely. If it should occur, do not induce vomiting, obtain medical advice. Wash with soap and large amounts of water. Remove contaminated clothing. Flush eyes with large amounts of tap water for at least 15 minutes . If symptoms or irritation occur, call a physician

FIRE FIGHTING MEASURES


For major fires, call the fire brigade immediately. Ensure an escape path is always available from any fire. In case of fire, use foam, dry chemical, carbon dioxide, vaporizing liquid or water delivered as a fine spray. Do not use water jets. Fires in confined spaces should be dealt with by trained personnel wearing approved breathing apparatus.

ACCIDENTAL RELEASE MEASURES


Personal Precautions: Keep the public away. Isolate and evacuate the area. Shut oX the source if safe to do so. Advise authorities if the substance has entered a watercourse or sewer. Notify local health and pollution control agencies if appropriate. Recover and return free products to proper containers. Use suitable absorbent materials such as vermiculite, sand or clay to clean up residual liquids.

HANDLING AND STORAGE


Precautions for Safe Handling: Avoid skin contact. Good working practices, high standards of personal hygiene and plant cleanliness must be maintained at all times. Whilst using, do not eat, drink or smoke. Wear appropriate gloves. Wash hands thoroughly after contact. Ensure good ventilation and avoid, as far as reasonably practicable, the inhalation and contact with vapors, mists or fumes which may be generated during use. If such vapor, mists or fumes are generated, their concentration in the workplace air should be controlled to the lowest reasonably practicable level. Avoid contact with eyes. If splashing is likely to occur then wear a full face visor or chemical goggles as appropriate. Use disposable clothes and discard them when soiled. Do not put soiled clothes into pockets. Take all necessary precautions against accidental spillage into soil or water.
Conditions for Safe Storage: Store under cover, away from moisture and sources of ignition. Do not overheat in storage.

EXPOSURE CONTROL/PERSONEL PROTECTION


Avoid, as far as reasonably practicable, inhalation of vapors, mists or fumes generated during use. If vapors, mists or fumes are generated, their concentration in the workplace air should be controlled to the lowest reasonably practicable level.

Respiratory Protection: If operations are such that the excessive generation and inhalation of vapors, mists or fumes may be anticipated, then respiratory equipment meeting appropriate requirements for mists, fumes and organic vapors should be worn.
Personal Protective Equipment: While handling, suitable protective clothing of an appropriate standard should be worn.

Depending upon the type of operation, this may include:
  • 1. Visor to protect face and head covering with neck flap
  • 2. Protective boots.
If skin contact is likely, wear impervious protective clothing and/or gloves. Protective clothing should be regularly dry-cleaned and laundered. Wash any contaminated underlying skin with soap and water.

PHYSICAL AND CHEMICAL PROPERTIES


APPEARANCE : Colourless, Clear and Bright
ODOUR: Petroleum Odour
pH: N/A
AROMATIC CONTENT: 16.6
FLASH POINT: 42°C.
TOTAL SULPHUR: 0.013
MELTING POINT: -20°C.
BOILING POINT: 140-240°C.
EVAPORATION RATE: 65(Et Et=1)-DIN 53170
VAPOUR PRESSURE: < 5kPa @20°C.
VAPOUR DENSITY: N/A

RELATIVE DENSITY : 0.775-0.790
WATER SOLUBILITY : NIL
SOLUBILITY IN OILS : 100%
AUTO-IGNITION TEMPERATURE : > 230oC
DECOMPOSITION TEMPERATURE : N/A
SURFACE TENSION : 0.0245 N/m @25oC
VISCOSITY : 0.95 m2/s @40°C.
BOILING POINT: 140-240°C.
EXPLOSIVE PROPERTIES : May form explosive mixture with air
OXIDIZING PROPERTIES : N/A
PARTITION COEFFICIENT(Kow) : N/A
UPPER/LOWER FLAM LIMITS : 7.0%-0.7%

STABILITY AND REACTIVITY


Chemical Stability: Products of this type are stable and unlikely to react in a hazardous manner under normal conditions of use. Hazardous polymerization reactions will not occur. This material is combustible.

TOXICOLOGICAL INFORMATION


Inhalation At normal ambient temperatures, this product will be unlikely to present an inhalation hazard because of its low volatility. This material contains polycyclic aromatic hydrocarbons (PCAH's) at low levels. The handling procedures and personal protective measures described should be followed to minimize employee exposure.
Ingestion Unlikely to be accidentally swallowed in view of the high handling temperatures. Except as a deliberate act, the ingestion of large amounts of product is unlikely. Ingestion of the product may cause nausea or diarrhoea. Ingestion of hot product will cause burns to the mouth, throat and stomach.

ECOLOGICAL INFORMATION


Ecotoxicity Unlikely to cause long-term eXects in the aquatic environment.
Persistence /Degradability: This product is not biodegradable.

DISPOSAL CONSIDERATIONS


Dispose of via an authorized person/ licensed waste disposal contractor in accordance with local regulations. Incineration may be carried out under controlled conditions provided that local regulations for emissions are met. Where possible arrange for the product to be recycled. Dispose of product and container carefully and responsibly. Do not dispose of near or into waterways, ditches or down drains.

TRANSPORT INFORMATION


This product is not classified as hazardous. Not covered by International regulation on the transport of dangerous goods (IMDG, IATA, ADR/RID); Not a marine pollutant UN No.: Not applicable

REGULATORY INFORMATION


US FEDERAL REGULATORY INFORMATION TSCA INVENTORY LISTING: INDUSTRIAL ORGANIC SOLVENT - CAS NO. 64742-88-7.

OTHER INFORMATION


DATE OF PREPARATION OR LAST REVISION OF MSDS : MAY 2024

CERTIFICATE OF ANALYSIS - INDUSTRIAL ORGANIC SOLVENT


# PARAMETERS UNIT TEST METHOD RESULTS
1 RELATIVE DENSITY(SG) @ 15oC Kg/L ASTM D 12980.782
2 DENSITY @ 15oC Kg/L ASTM D 1298 0.775
3 ASTM COLOUR - ASTM D 15001.0.5
4 KINEMATIC VISCOSITY @ 40oC cSt ASTM D 4451.102
5 OBSERVED FLASH POINT °C. ASTM D 93 42
6 TOTAL SULPHUR CONTENT ppm ASTM D 4249 72
<
# DISTILLATION: UNIT TEST METHOD RESULTS
1 Initial Boiling Point (IBP) °C. ASTM D 2887 166
2 5% Recovered at °C. ASTM D 2887 171
3 10% Recovered at °C. ASTM D 2887 175
4 15% Recovered at °C. ASTM D 2887 178
520% Recovered at °C. ASTM D 2887 182
6 25% Recovered at °C. ASTM D 2887 184
7 30% Recovered at °C. ASTM D 2887 186
8 35% Recovered at °C. ASTM D 2887 188
9 40% Recovered at °C. ASTM D 2887 1G0
10 45% Recovered at °C. ASTM D 2887 1G2
11 50% Recovered at °C. ASTM D 2887 1G4
12 55% Recovered at °C. ASTM D 2887 1G6
13 60% Recovered at °C. ASTM D 2887 1G8
14 65% Recovered at °C. ASTM D 2887 201
15 70% Recovered at °C. ASTM D 2887 203
16 75% Recovered at °C. ASTM D 2887 206
17 80% Recovered at °C. ASTM D 2887 20G
18 85% Recovered at °C. ASTM D 2887 213
18 90% Recovered at °C. ASTM D 2887 217
18 98% Recovered at °C. ASTM D 2887 236
18 Final Boiling Point (FBP) °C. ASTM D 2887 237
18 Aromatics %(v/v) ASTM D 2887 16.2